|
1. How to Install Underground Fuel Storage Tanks and Piping - 381 pages. Textbook for UST Installer Certification Exams. Incorporates PEI RP 100,
API 1615, NFPA 30, 30A, 10, 70, manufacturers installation instructions, 40CFR 280 as well as unpublished helpful hints from UST installers - you can benefit from
their mistakes. Subjects covered: Pre-Installation Testing, Excavation, Backfilling, Anchoring, Spill & Overfill Prevention, Leak Detection, Piping, Cathodic Protection and Electrical. Cost $100.00 2. How to How to Comply with SPCC Regulations - 177 pages. A comprehensive text on the procedures to properly Shop Fabricated Aboveground Tanks used to store petroleum products. Subjects covered: General requirements of the SPCC Regulations, Pre-installation testing and inspection, tank installation, pump installation, venting, piping and fittings, corrosion protection, dikes, overfill prevention, fire protection and identification, electrical installation, STI SP001 standard, other considerations. Cost $75.00 3. A Contractor's Guide to UST Closures - 149 pages. A comprehensive textbook used as a study guide for preparing to take UST Remover/Decommissioning Certification exams. This book incorporates industry practices, API recommended practices, NFPA 30 & 30A codes as well as many other safety procedures not found in any other publication. There is a complete section on the proper use, calibration, maintenance and repair of LEL and oxygen meters. One book covers all regulations with the exception of state & local specific codes and regulations.Cost $75.00. 4. TANK TRUCK DRIVERS SAFETY COURSE MANUAL - 27 pages. Most serious accidents at service stations involve the transport driver. This manual illustrates responsibilities and procedures of tank truck drivers when making deliveries to aboveground and underground storage tanks. Cost $20.00. 5. How to Perform a UST Compliance Inspection - 197 Pages. A step by step procedure to inspect Underground Storage Tanks for Compliance with Federal and State regulations as well as fire codes and OSHA regulations. Comes complete with a sample checklist. Cost $75.00. 6. UST Operators Training Course - 2 manuals: 137 page training manual and a loose leaf bound forms records manual describing when to do what. This is a complete course for any individual responsible for underground storage tanks. It covers federal UST regulations, industry standards, fire codes and OSHA rules. The course includes a section on how to train a new employee, such as a cashier, in less than one hour. Cost $145.00. 7. How to Test Cathodic Protection on Underground Storage Tanks - 125 pages. This text is an easy to read step-by-step manual describing how to test galvanic and impressed current cathodic protection on underground storage tanks. The text gives illustrations on testing locations and the calibration of reference electrodes. Included in the text are prepared checklists and record keeping forms to document your test results. One of the easiest to read manuals on cathodic protection. Cost $90.00. 8. Solutions to New Underground Storage Tank Problems - 123 pages. New problems on underground storage tanks are constantly occurring. This book has taken some of the more common problems and condensed them into one book. Some of the situations covered are: New NFPA 30A revisions, problems with ethanol & bio-diesel, how to test continuity on petroleum dispensers, 5 situations where ball float valves should not be used, problems with remote fills on underground storage tanks and many more topics too numerous to mention in this short space. Cost $75.00. 9. OSHA 8 Hour Refresher On-Site Supervisor's Course for UST Sites - 287 pages. This course meets the requirements of both the OSHA HAZMAT annual refresher course and UST continuing education in states where our course is accepted. The course focuses on OSHA regulations directly related to Underground Storage Tank contractors. Topics include: Confined Space Entry, Lockout/Tagout, Excavation Regulations, monitoring instruments, etc. Cost $75.00. 10. Underground Storage Tank Technician's Training Course - 203 pages. This course is intended to provide a basic knowledge of the UST regulations, industry standards, fire codes and safety procedures that apply to employees who work on parts of an underground storage system but do not install or remove underground storage tanks. Technicians that replace and install line leak detectors, safety shear valves, check valves, flex connectors or service or replace sensors inside sumps or tanks need a basic knowledge of the sections of the regulations that apply specifically to their job title. Cost $75.00. |